Sun Joe pressure washer GFCI won’t reset – Possible reasons with solutions

Dealing with the pressure washer GFCI by breaking the regular schedule isn’t desired by anyone. Unfortunately, the GFCI of the Sun Joe pressure washer may not be reset for some reason. People may face problems with GFCI even if it’s a brand new pressure washer. 

Hence, you need to find a proper solution instantly if your Sun Joe pressure washer GFCI won’t reset. But, it’ll be the best move to know about the possible reasons behind this incident first. Taking proper steps according to the problem will be convenient and time-saving for the owner.

The presence of a faulty GFCI outlet is the commonest among all reasons. Besides, it can be a connection issue or circuit breaker issue. GFCI plug also can be damaged rarely. Whatever the problem is, you can fix it without appointing an expert. 

Sun Joe pressure washer GFCI won’t reset- possible reasons with solutions

Some conventional reasons lie behind not resetting the GFCI. You need to observe the problem and find out the possible solutions then. Here are some irritating problems on Sun Joe pressure washer GFCI won’t reset with solutions. 

Loose connection of the GFCI outlet

Finding a loose connection between wire connectors isn’t a difficult issue. You can fix this problem by reinstalling the connector. Most of the time, outlets are connected with an electrical box. It stays too far away behind the wall. Their unstable position could bump or jostle the wire loose. Pressure washer GFCI won’t reset for the loose connection of this outlet. 

So, you need to fix the loose connection of the outlet. Here are some elaborated steps so that you can fix the GFCI outlet without someone’s assistance. 

How to fix a loose GFCI outlet:

1. First of all, you need to turn off the power of the target place. For additional safety, you can turn off the main breaker. This action will decrease your chance of an accident to the minimum. Now, come towards the loose GFCI outlet and move on.
2. Test that the power has turned off successfully. You can use your wire tester to be assured. It’s prohibited to proceed until being sure about the discontinuities of the electricity. 
3. Now, you need to unscrew the desired outlet using the screwdriver. After that,  bring that out carefully.
4. You need to place the outlet shims now. Those must be placed on the outlet screws. If there is any gap between the screws and the recessed box, it will cover that. The number of shims may vary based on the recession of the box. 
5. Last, of all, replace the outlet carefully and attach the screws. Hope that you won’t find your GFCI outlet loose anymore. 

GFCI outlet receptacle is gone

Is the pressure washer’s GFCI constantly coming out of the GFCI outlet? Maybe, the issue is with the GFCI outlet receptacle. The two little holes where you plug your plugs are known as receptacles. It’s a common issue that the receptacle of the old outlet gets damaged without any reason. In this circumstance, the best move is to replace the whole outlet. 

Here you learn about fixing a receptacle outlet by transplanting a new GFCI outlet. However, you need some tools like an insulated screwdriver, a new GFCI outlet, pliers, and a tester. Get all the items precisely before starting the main job. 

How to fix a GFCI outlet receptacle by replacing it:

1. Turn the power off at first. You can turn the main breaker off to maintain the appropriate safety. 
2. You need to remove the faceplate now. Two screws hold the faceplate firmly. Use the screwdriver to unscrew those. After that, put the screws along with the plate aside. It’s recommended to put the screws upside down on the faceplate. This action will decrease the possibility of losing the screws. 
3. Now, remove the outlet carefully. Two long screws must hold the outlet with the box. You need to remove the screws before withdrawing the outlet.
4. You need to check the black wire using the non-contact tester. After ensuring your safety, prepare the new outlet for replacing it. 
5. Wiring the outlet with the exact connector is important. As there are five different connectors, you may get confused. So, be careful in this step while wiring with the connectors.
6. Last, of all, push the wires into the hole and move to reinstall it.
7. Replacing the outlet is kind of doing the initial steps reversely. After carefully placing the outlet into the box, tighten it with the screws. Then replace the cover plate and test if it works. 

Overloaded circuit

Each electric wire has limitations of its amperage flowing. The wire can’t handle the extra amperage flow through it. An inappropriate amperage flow is possible when there are defective appliances. It breaks the circuit without a few moments. Sun Joe pressure washer fuse location also may damage due to an overloaded circuit. 

Overloading isn’t a very common issue in the case of GFCI outlets. However, you can conquer the overloading issue by maintaining some easy steps. 

How to eradicate overloaded circuit issues:

1. Unplug all the connected appliances including the Sun Joe pressure washer.
2. You need to reset the circuit in this step. The circuit can be reset on the fuse box. 
3. Wait several minutes in front of the fuse box now. 
4. After a certain time, plug-in any appliance to check the issue. Then plug the pressure washer if everything seems okay. That’s it.

However, your overloading issue may not dispel after this effort. You need to purchase and replace a dedicated circuit and outlet then. 

FAQ

Having some questions on the Sun Joe pressure washer GFCI resetting issue? This part might be helpful for you. 

How do I know if my GFCI outlet is faulty?

Push the reset button on the outlet first. Now, uncover the cover plate and dispose of the GFCI outlet from its place. Push the black button after observing the red button is off. Not popping up the red button indicates that the GFCI outlet is faulty. 

How do you fix a GFCI plug on a pressure washer?

You can fix the GFCI plug by purchasing and substituting a new one. Open the two screws on the bottom side to remove the old GFCI plug. Then, unscrew the cord from the GFCI plug. Then, substitute with a new one and reversely follow the disassembling path. 

Is it better to use a GFCI outlet or breaker?

GFCI breakers aren’t easy to install like GFCI receptacles. You need not go for a GFCI breaker if it’s all about protecting a single location. However, the GFCI breakers don’t require the installation of an entire GFCI breaker panel.

More pressure washer repair related article at howtofixup

Why Is Your Sun Joe Pressure Washer Soap Not Working?

Sun Joe Pressure Washer Troubleshooting

Simpson Water Pressure Unloader Valve: Everything You Should Know

Greenworks Pressure Washer Troubleshooting

Conclusion

As a pressure washer is an instrument, it normally comes with some devastating problems. You can find Sun Joe pressure washer GFCI won’t reset without severe notice.  In that case, your task is to find the exact reason lying behind this problem first. 

You must have ideas on some prime reasons revolving around the existing issue. GFCI may face an unexpected problem with the GFCI outlet. Or, it can be a damaged GFCI plug. So, whatever the problem is, it won’t be an issue to fix without the professionals.